Lidar - motor mount added

Since I have been really busy working on other embedded projects, it has been a little difficult for me to finish up the lingering project over the last few weeks. However, I was able to finally had the motor mount, additional pulley and improve the inner fasteners.

The full stand is about 4.5" high and about 5-6" wide. It is still reasonably sized. Mounting it on a robot should be the interesting part. I am still playing with the optical interrupt triggers. Maybe I will get more time soon...

stereo_cyclops cad posted...

I just added the cad model to the jetbot repository. Obviously, if you are an onshape user, you can copy the entire workspace and edit the model at your heart's content.

Search for 'stereo-camera-case' to find the model. 3D prints away!

stereo_cyclops released...

I posted stereo_cyclops, in the spirt of hacking, for all makers and the open source robotics community.

github.com/hhony/jetbot

It is a jetson compatible repo, for building a stereo camera, nickname: stereo_cyclops.

Lidar - full redesign

After the first prototype print, I found several mechanical issues which could have been avoided had I taken the time to rethink the placement solution. I redesigned the quadrature encoder wheel to be something closer to what a shaft encoder (in principle) would do. 

I have also considered using an absolute encoder and gear ratios. I know that I have less to worry about in regards to 'belt slip' with the use of a timing pulley. However, I am always concerned about the wear and tear causing slip than anything else. The most common mistake when building a timing pulley system is tightening the belt too tight. This will eventually deteriorate the belt and slip will be introduced before belt breakage occurs.

Obviously the best redesign of the entire solution (if I were not already committed to using off-the-shelf components) would be to redesign the slip-ring itself... I have considered this task, several times already. 

The main issue I have against redesigning the slip-ring is that: 

1. I would not be using off-the-shelf components which would be easily source-able for anyone else to build one of these. And... 
2. I have been down this road before on another robot. Designing a slip-ring can become hard to manufacture... but I might take another stab at it eventually (with all my lessons learned up front).

I oriented the optical interrupters to be above each other. Overall I think the height increased by 5mm or so in Z... it's not a bad trade off since the horizontal is about 9mm shorter in X now. I also drastically increased the wire feed hole through the lidar case mount - through the top). Unfortunately it is not visible from the above view.

I also added zero-ing text so it is easier to explain the quadrature encoding to others. I had so many people ask me where zero was, I decided to just make it visible for all to see, rather than searching the entire part for the misaligned holes.

So, now I feel the quadrature encoding is much more clear for others from the above picture.

Lidar - printing design without support material

For having zero mechanical degree, I can't really complain with the utility at which I've applied my art degree from a former career. There is a certain part of the manufacturing process which relies on general aesthetics and functionality in order to design something that looks like it will work. 

I have separated the spinning assembly into 5 components now. And the fact that I don't even have to use support material anymore means that the prints are looking great. 

Shortly after my last post I redesigned every piece of the top assembly to print on a flat surface. I have a strange attraction to components with tabs... there's something surprisingly satisfying about your 3D printed part just snapping together just moments after it is off the print bed.

The encoder wheel has a groove in the bottom with a few mounting tab slots (above in green color). The encoder ring that isolates the two optical detectors, just slides right into the bottom of the part. It will need a few small epoxy beads on the above tab insides. And the rest is smooth printing all around.

Next tasks:

• Design motor mount
• Design motor shaft coupling pulley
• Modify existing lidar base to accomodate motor mount
• Print and start coding

Lidar - mount threaded...

Redesign of the encoder wheel needed to happen today. I did fit the parts and I'm quite proud of how it is turning out. 

The mounted pulley is flush just like the CAD. However, I found an issue with the support material because my second pass on the design just wasn't good enough for manufacturability. I need really flat surfaces from the raft on the encoder to improve the overall print quality.

I have separated the pulley pins into threaded rods, and I am using them to the mount the lidar on top of the pulley as well. 

The isolation ring on the bottom has become it's own slip in part. I will likely have to epoxy it into the channel for now. This will provide prints with zero support material for the encoder wheel - and this should reduce the noise on the sensor by quite a lot. I may add snap tabs (like I already did for the lidar mount).

The top of the pulley also has the three snap tabs. I am quite please with how these turned out. They snap right into to the lidar mount and the fit is pretty snug. I seem to have sized it very closely.

Lidar - 1st pass, and improvements

The print came out great, for such a complicated shape. Part of this exercise is to push the limits of the printer, and the other part of this exercise is to design it better for printing based on what is discovered in the process.

Problem spots which were noted at time of beginning to print:

1. The mask for the encoder emitter detector sensor makes printing this structure with the modern support structures almost impossible because of the density of small features in the model. The durability of the mask is compromised by the proximity to support material.
2. The manufacturability of this object is much lower than it could be. The issue is that the assembly is not that modular for repairing the unavoidable wear and tear on a spinning part.

Ways to improve design:

• Create large printable planes and minimize support material needed to improve structural integrity of part. The easiest way to to this is raise the interior of the top of the encoder wheel.

• Separating the gear component into its own part will ease repair of the component by adding accessibility. Likely, I will take this idea further and replace the the plastic pins with bores for some pins. And these pins will be threaded from either side of the pulley bores by a threaded inset. The pins will sandwich the pulley and the encoder between the laser mount bracket and the slipring.

Lessons learned should never be passed over too quickly:

From experience, while working on robots from the field for a few years... The repair of the robot is unavoidable, just as your car will not run forever without maintenance. Making that repair process easier or more difficult - is up to the designer and the manufacturer.

Note, I needed to add some relief into the bottom of the encoder sensor cover. This also looks much easier to assemble. The previous concern was for upward light into the detector, but the new shelf adds the needed emitter/detector isolation.

Future improvements:

• threaded pins inserts 
• bore holes through pulley with threaded inset mates for pins 
• add cable management into the base and encoder cap